|
|
|
FiberMix 2304-120
|
| Standalone, 4 E1 channels optical
multiplexer, 4 10/100 RJ45, remote SNMP-management, SSF, Dual WL, 1310nmTX
1550nmRX, AC 115V or 230V, DC – 48V |
|
FiberMix 2504-120
|
| Standalone, 4
E1 channels optical multiplexer, 4 10/100 RJ45, remote SNMP-management, SSF, Dual WL, 1550nmTX
1310nmRX, AC 115V or 230V, DC –48V |
|
|
|
View Larger Picture
|
Dynamix FiberMix 2x04-120 Ethernet multiplexer is an ideal transmission device of optical fiber for
point to point networks, middle and small capacity networks, such as wireless communication base
stations, private communication networks and switch networks.
Dynamix FiberMix 2x04-120B provides 4 E1 links and 4 Ethernet ports Fast Ethernet. It can be applied to either local management or to remote management.
The issues of improvement and management of available capacities of leased fiber are essential for carrier that are looking for the way to transfer maximum volumes data via existing
network without any additional cost. Dynamix FiberMix 2x04-120 series products are flexible devices, operating at rate: 2.048Mbps and equipped with following interface which can be used as 4-port Ethernet switch or as 4 individual Ethernet ports shared 100Mbps for dedicated services.
Error detection procedures are supported by test loop-back and each E1 channel can
be diagnosed by loop-back.
|
User's manual
FiberMix
2304-120
190 Kb
FiberMix
2504-120
190 Kb
Quick start
|
|
|
|
| • |
Multiplex 4 E1 inputs and 4 Ethernet inputs to one fiber line |
| • |
Standalone unit |
| • |
Single fiber solution (WDM) available |
| • |
Transmission distance up to 120km |
| • |
Remote SNMP-management |
| • |
supported by test loop-back and each E1 channel can be diagnosed by loop-back |
| • |
Full alarm indicator |
| • |
Local and remote alarm can be show at one time |
| • |
Provide function with E1 branch loop-back test for easy maintain |
| • |
Provide Ethernet interface with 4 ports (10/100Mbps auto-adaptive) |
| • |
Standalone units provide built-in power supply |
| • |
Support communication or insulation among Ethernet ports |
| • |
Support Ethernet full duplex IEEE802.3x and half duplex flow control of backpressure |
| • |
Support either network management (NM) or remote management. Could select NM interface RS-232 or RS-485 |
 Back to Top
|
|
|
|
|
|
| | Multiplex 4 E1 inputs and 4 Ethernet inputs to one fiber line |
| Support Data rate |
| | 4*2.048Mbps and wire-speed 100Mbps |
| Interface |
| | 4*E1 (75ohm or 120ohm RJ45). 4*RJ45 |
| E1 Ethernet interface technical indicator |
| | IEEE 802.3 Ethernet |
| | IEEE 802.3u Fast Ethernet |
| | IEEE 802.3q |
| | IEEE 802.3d Spanning Tree |
| Line |
| | 1310 nm multimode/single mode, 1550 nm DFB single mode (SC connector) |
| Transmission
distance |
| | up to 120km; WDM solution is up to 60km |
| |
| | Provide function with E1 branch loop-back test for easy maintain |
| | Provide Ethernet interface with 4 ports (10/100Mbps auto-adaptive) |
| | Support maximum Ethernet data frame length up to 1916 bytes |
| | Adopt large scale ASIC chip, low power consumption, 4 layers PCB, and high dependability |
| | SNMP management |
| | Standalone units provide built-in power supply |
| Dimensions |
| | standalone unit:
320(W)*38(H)*160(D) (mm) |
| Power |
| | Supply:
115/230VAC
-48DC |
| | Consumption:
25W |
| Environment |
| | 0~45 degrees Centigrade operating less than 90% humidity (25 degrees
Centigrade) |
| Compliance |
| | CE certification |
|
|
Back to Top
|
|
|
|
|
|
|
|
| FiberMix 2304-120 |
Standalone, 4 E1 channels optical multiplexer, 4 10/100 RJ45, remote SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX, AC 115V or 230V, DC – 48V |
| FiberMix 2504-120 |
Standalone, 4 E1 channels optical multiplexer, 4 10/100 RJ45, remote SNMP-management, SSF, Dual WL, 1550nmTX 1310nmRX, AC 115V or 230V, DC –48V |
| FiberMix 2504-120 |
Standalone, 4 E1 channels optical multiplexer, 4 10/100 RJ45, remote SNMP-management, AC 115V or 230V, DC –48V |
|
|
Back to Top |
|
|
Also see the products of this group:
|
|
G.703
E1-U/ FE1/ FE1-A Single Port E1 and Fractional E1 Access Unit
|
|
FiberMix 903-V35FE1
V.35 to E1
fractional Interface Converter
|
|
FiberMix 904-V35FE1
Module, V.35 to transparent or fractional E1 interface converter, SNMP-management
|
|
FiberMix 907-EV35 Standalone 10BaseT to
V.35 Converter
|
|
FiberMix 905-EE1 Standalone 10Mbps on Transparent or Fractional
E1 Converter
|
|
FiberMix 001-1 1-slot Chassis
|
|
FiberMix 002-4 4-slot Chassis (managed)
|
|
FiberMix 002-16 16-slot Modular Converter Chassis with SNMP Management
|
|
FiberMix 001-NMS1 Master Management Agent Module for 3U Chassis
|
|
FiberMix 001-NMS2 Slave Management Module for 3U Chassis
|
|
FiberMix 004-16NMS1 Master Management Agent Module for 10U Chassis
|
|
FiberMix 004-16NMS2 Slave Management Module for 10U Chassis
|
|
FiberMix 802-60 Module, 2 E1 channels optical
multiplexer,
SNMP-management
|
|
FiberMix 803-120 Standalone, 4 E1 channels
optical multiplexer, remote SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX, 19” 1U
chassis, AC 115V or 230V, DC – 48V
|
|
FiberMix 805-120B Standalone, 4 E1
channels optical multiplexer, remote SNMP-management,
SSF, Dual WL, 1550nmTX 1310nmRX, 19” 1U chassis, AC 115V or 230V, DC –48V
|
|
FiberMix 804-60B Module, 2 E1 channels optical multiplexer, SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX
|
|
FiberMix 806-60B Module, 2 E1 channels optical multiplexer, SNMP-management, SSF, Dual WL, 1550nmTX 1310nmRX
|
|
FiberMix 803-480B Standalone, 16 E1 channels optical multiplexer, SSF, Dual WL, 1310nmTX 1550nmRX, 19” 1U chassis, AC 115V or 230V/DC –48V
|
|
FiberMix 805-480B Standalone, 16 E1 channels optical multiplexer, SSF, Dual WL, 1550nmTX 1310nmRX, 19” 1U chassis, AC 115V or 230V/DC –48V
|
|
FiberMix 805-240B Standalone, 8 E1 channels optical
multiplexer, remote SNMP-management SSF, Dual WL, 1550nmTX 1310nmRX, 19” 1U
chassis, AC 115V or 230V/DC –48V
|
|
FiberMix 2304-120 Standalone, 4 E1 channels optical multiplexer, 4 10/100 RJ45, remote SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX, AC 115V or 230V, DC – 48V
|
|
FiberMix 2504-120 Standalone,
4 E1 channels optical multiplexer, 4 10/100 RJ45, remote SNMP-management,
SSF, Dual WL, 1550nmTX 1310nmRX, AC 115V or 230V, DC –48V
|
|
FiberMix 2401-30, FiberMix 2601-30 Module
- PDH Fiber Optical Multiplexers - 1 single strand fiber optical
port (Single mode 1310nm TX 1550nm RX and 1550nm TX 1310nm RX), 1 E1 port and 1 Fast-Ethernet port
|
|
FiberMix 2401-60, FiberMix 2601-60 Module-
PDH Fiber Optical Multiplexers - 1 single strand fiber optical
port (Single mode 1310nm TX 1550nm
RX and 1550nm TX 1310nm RX), 2 E1 ports and 1 Fast-Ethernet port
|
|
FiberMix 3100-155
SDH Multi-Service multiplexer
|
|
|
