FiberMix 802-60 Module, 2 E1 channels optical multiplexer, SNMP-management

FiberMix 802-60

Module, 2 E1 channels optical multiplexer, SNMP-management

Specification | Front panel | Ordering information

The issues of the proper organization and management of available capacities of leased fiber are essential for companies that are looking for the way to transfer maximum volumes data via existing network without any additional cost. FiberMix 80x-60B/FiberMix 80x-60B-FV35 series are flexible devices, operating at the rate of 2.048Mbps (transparent) or N × 64 (fractional) and equipped with the interfaces of V.35 and G.703.

Error detection procedures are supported by loop-back function and each E1 channel can be diagnosed by loop-back function. The use of an optional WDM fiber doubler is an improvement to cable capacities as different wavelengths are received and transmitted along a single fiber.

FiberMix 802-60B is an ideal transmission device of optical fiber for point to point networks, middle and small capacity networks, such as wireless communication base stations, private communication networks and switch networks. It can be applied to either public networks or various private networks. FiberMix 802-60B module provides 2 E1 links (equivalent to 60 voice channels).

User's manual
250 Kb

Quick start

•

Multiplex two electrical inputs to one fiber line

•

Slide-in module in 3U high chassis or standalone unit

•

Various interfaces and connectors available

•

Single fiber solution (WDM) available

•

Transmission distance up to 120km

•

Error detection procedures are supported by loop-back function and each E1 channel can be diagnosed by loop-back function. The use of an optional WDM fiber doubler is an improvement to cable capacities as different wavelengths are received and transmitted along a single fiber.

Data rate
	2.048Mbps (transparent) or N*64 (fractional)

Interface
	V.35 (M34) and E1 (75ohm or 120ohm RJ45)

Line
	1310nm multimode/single mode, 1550nm DFB single mode (SC connector)

Transmission distance
	up to 120km; WDM solution is up to 60km

SNMP management
	via slide-in modular agent in the chassis, in-band management for the remote unit
	Standalone units provide built-in power supply.

Dimensions
	standalone unit: 130(W)43.6(H)150(D) (mm) 142(W)38(H)178(D) (mm)
	modular unit:91(W)25(H)155(D) (mm)

Power
	Supply: 115/230VAC -48DC
	Consumption: 5W

Environment
	0~45 degrees Centigrade operating less than 90% humidity (25 degrees Centigrade)

Compliance
	CE certification

Front panel FiberMix 802-60 Module, 2 E1 channels optical multiplexer, SNMP-management

FiberMix 802-60	Module, 2 E1 channels optical multiplexer, SNMP-management
Note:	The default optical port of FiberMix 80X is S1, the transmission distance of S1 is 0~25km. The longer transmission distance models can be customized according to customer requirement. The S2 model provides a transmission distance from 10 to 60km, and the S3 model from 15 to 120km.

Also see the products of this group:

G.703 E1-U/ FE1/ FE1-A Single Port E1 and Fractional E1 Access Unit

FiberMix 903-V35FE1 V.35 to E1 fractional Interface Converter

FiberMix 904-V35FE1 Module, V.35 to transparent or fractional E1 interface converter, SNMP-management

FiberMix 907-EV35 Standalone 10BaseT to V.35 Converter

FiberMix 905-EE1 Standalone 10Mbps on Transparent or Fractional E1 Converter

FiberMix 001-1 1-slot Chassis

FiberMix 002-4 4-slot Chassis (managed)

FiberMix 002-16 16-slot Modular Converter Chassis with SNMP Management

FiberMix 001-NMS1 Master Management Agent Module for 3U Chassis

FiberMix 001-NMS2 Slave Management Module for 3U Chassis

FiberMix 004-16NMS1 Master Management Agent Module for 10U Chassis

FiberMix 004-16NMS2 Slave Management Module for 10U Chassis

FiberMix 802-60 Module, 2 E1 channels optical multiplexer, SNMP-management

FiberMix 803-120 Standalone, 4 E1 channels optical multiplexer, remote SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX, 19” 1U chassis, AC 115V or 230V, DC – 48V

FiberMix 805-120B Standalone, 4 E1 channels optical multiplexer, remote SNMP-management, SSF, Dual WL, 1550nmTX 1310nmRX, 19” 1U chassis, AC 115V or 230V, DC –48V

FiberMix 804-60B Module, 2 E1 channels optical multiplexer, SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX

FiberMix 806-60B Module, 2 E1 channels optical multiplexer, SNMP-management, SSF, Dual WL, 1550nmTX 1310nmRX

FiberMix 803-480B Standalone, 16 E1 channels optical multiplexer, SSF, Dual WL, 1310nmTX 1550nmRX, 19” 1U chassis, AC 115V or 230V/DC –48V

FiberMix 805-480B Standalone, 16 E1 channels optical multiplexer, SSF, Dual WL, 1550nmTX 1310nmRX, 19” 1U chassis, AC 115V or 230V/DC –48V

FiberMix 805-240B Standalone, 8 E1 channels optical multiplexer, remote SNMP-management SSF, Dual WL, 1550nmTX 1310nmRX, 19” 1U chassis, AC 115V or 230V/DC –48V

FiberMix 2304-120 Standalone, 4 E1 channels optical multiplexer, 4 10/100 RJ45, remote SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX, AC 115V or 230V, DC – 48V

FiberMix 2504-120 Standalone, 4 E1 channels optical multiplexer, 4 10/100 RJ45, remote SNMP-management, SSF, Dual WL, 1550nmTX 1310nmRX, AC 115V or 230V, DC –48V

FiberMix 2401-30, FiberMix 2601-30 Module - PDH Fiber Optical Multiplexers - 1 single strand fiber optical port (Single mode 1310nm TX 1550nm RX and 1550nm TX 1310nm RX), 1 E1 port and 1 Fast-Ethernet port

FiberMix 2401-60, FiberMix 2601-60 Module- PDH Fiber Optical Multiplexers - 1 single strand fiber optical port (Single mode 1310nm TX 1550nm RX and 1550nm TX 1310nm RX), 2 E1 ports and 1 Fast-Ethernet port

FiberMix 3100-155 SDH Multi-Service multiplexer

If you need further information, please fill out this form below

What kind of information would you like to receive from us?

Please fill out the contact information:
First name/Last name: *
Company: *
E-mail: *
Your phone (country/city code): *

* Indicated a required field

DYNAMIX^®