FiberMix 903-V35FE1 V.35 to E1 Interface Converter

FiberMix 903-V35FE1

V.35 to E1 Interface Converter

FiberMix 904-V35FE1

Module, V.35 to transparent or fractional E1 interface converter, SNMP-management

Specification | Front panel | Application | Ordering information

$FiberMix 903-V35FE1 V.35 to E1 fractional Interface Converter$
FiberMix 903-V35FE1

$FiberMix 904-V35FE1 Module, V.35 to transparent or fractional E1 interface converter, SNMP-management$
FiberMix 904-V35FE1

View Larger Picture

FiberMix 90x-V35FE1 converter provides an optimum solution for transparent G.703 signals. It supports such standard interface type as V.35. Error detection procedures are supported by loop-back function

FiberMix 903-V35FE1 is a standalone interface converter. It provides signal conversion between V.35 and transparent E1 or fractional E1, and can be used for V.35 signal over E1 network transmission.
As growing utilization of E1 recources, many date transmission solutions using E1 link are accepted by users at large.
FiberMix 903 - V35FE1 is standalone equipment, with built-in power supply, and can be placed on the desk.

User's manual
       FiberMix 903 Rev C
       342 Kb
       FiberMix 903 Rev B
       342 Kb
       FiberMix 904 344 Kb

Quick start

•

Optimum solution for appropriate and exten sive utilization of leased lines

•

Slide-in module or standalone unit

•

Data conversion from V.35 format into G.703

•

FiberMix 90x-V35FE1 and FiberMix 90x-V35E1 converter provides an optimum solution for transparent G. 703 signals. It supports such standard interface type as V.35. Error detection procedures are supported by loop-back function

•

Standalone units provide built-in power supply

•

Clock mode: master, slave and terminal clock mode

•

SNMP managementvia slide-in modular agent in the chassis

•

The module can be plugged into FiberMix 001-1, FiberMix 001/002-4 and FiberMix 002-16 chassis.

E1 Interface
	Bit Rate: 2048kbps±50ppm
	Line Code: HDB3
	Input Impedance: 75ohm (unbalanced BNC connector) 120ohm (balanced RJ45 connector)
	Electrical Characteristics:IITU-T G.703
	Frame Structure:ITU-T G.704
	Jitter Performance:ITU-T G.823

V.35 interface
	Physical Characteristics:Compliant to V.35 interface standard
	Interface Type: HDB26 for module, M34 for standalone
	Working Mode:DCE
	Bit Rate: N*64kbps (N=1~31) at fractional E1 2.048Mbps at transparent E1 mode

Dimensions
	standalone unit: 120(W)39(H)156(D) (mm)
	modular unit: 91(W)25(H)155(D) (mm)

Power Supply
	115/230VAC -48DC
	Power Consumption - 3W

Environment
	0~45 degrees Centigrade operating less than 90% humidity (25 degrees Centigrade)

Compliance
	CE certification

$Front panel FiberMix 903-V35FE1 V.35 to E1 fractional Interface Converter$
FiberMix 903-V35FE1

$Front panel FiberMix 904-V35FE1 Module, V.35 to transparent or fractional E1 interface converter, SNMP-management$
FiberMix 904-V35FE1

$Application FiberMix 903-V35FE1 V.35 to E1 fractional Interface Converter$

Point to point application. It enables routers to utilize one E1 link transmission. The application provides two working modes: transparent E1 and fractional E1. Master clock, slave clock and V.35 terminal clock can be configured. Compact standalone units are applied, it easy for installation and maintenance.

FiberMix 903-V35FE1	Standalone, V.35 to transparent or fractional E1 interface converter, AC 115V or 230V/DC –48V
FiberMix 904-V35FE1	Module, V.35 to transparent or fractional E1 interface converter, SNMP-management

Also see the products of this group:

G.703 E1-U/ FE1/ FE1-A Single Port E1 and Fractional E1 Access Unit

FiberMix 903-V35FE1 V.35 to E1 fractional Interface Converter

FiberMix 904-V35FE1 Module, V.35 to transparent or fractional E1 interface converter, SNMP-management

FiberMix 907-EV35 Standalone 10BaseT to V.35 Converter

FiberMix 905-EE1 Standalone 10Mbps on Transparent or Fractional E1 Converter

FiberMix 001-1 1-slot Chassis

FiberMix 002-4 4-slot Chassis (managed)

FiberMix 002-16 16-slot Modular Converter Chassis with SNMP Management

FiberMix 001-NMS1 Master Management Agent Module for 3U Chassis

FiberMix 001-NMS2 Slave Management Module for 3U Chassis

FiberMix 004-16NMS1 Master Management Agent Module for 10U Chassis

FiberMix 004-16NMS2 Slave Management Module for 10U Chassis

FiberMix 802-60 Module, 2 E1 channels optical multiplexer, SNMP-management

FiberMix 803-120 Standalone, 4 E1 channels optical multiplexer, remote SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX, 19” 1U chassis, AC 115V or 230V, DC – 48V

FiberMix 805-120B Standalone, 4 E1 channels optical multiplexer, remote SNMP-management, SSF, Dual WL, 1550nmTX 1310nmRX, 19” 1U chassis, AC 115V or 230V, DC –48V

FiberMix 804-60B Module, 2 E1 channels optical multiplexer, SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX

FiberMix 806-60B Module, 2 E1 channels optical multiplexer, SNMP-management, SSF, Dual WL, 1550nmTX 1310nmRX

FiberMix 803-480B Standalone, 16 E1 channels optical multiplexer, SSF, Dual WL, 1310nmTX 1550nmRX, 19” 1U chassis, AC 115V or 230V/DC –48V

FiberMix 805-480B Standalone, 16 E1 channels optical multiplexer, SSF, Dual WL, 1550nmTX 1310nmRX, 19” 1U chassis, AC 115V or 230V/DC –48V

FiberMix 805-240B Standalone, 8 E1 channels optical multiplexer, remote SNMP-management SSF, Dual WL, 1550nmTX 1310nmRX, 19” 1U chassis, AC 115V or 230V/DC –48V

FiberMix 2304-120 Standalone, 4 E1 channels optical multiplexer, 4 10/100 RJ45, remote SNMP-management, SSF, Dual WL, 1310nmTX 1550nmRX, AC 115V or 230V, DC – 48V

FiberMix 2504-120 Standalone, 4 E1 channels optical multiplexer, 4 10/100 RJ45, remote SNMP-management, SSF, Dual WL, 1550nmTX 1310nmRX, AC 115V or 230V, DC –48V

FiberMix 2401-30, FiberMix 2601-30 Module - PDH Fiber Optical Multiplexers - 1 single strand fiber optical port (Single mode 1310nm TX 1550nm RX and 1550nm TX 1310nm RX), 1 E1 port and 1 Fast-Ethernet port

FiberMix 2401-60, FiberMix 2601-60 Module- PDH Fiber Optical Multiplexers - 1 single strand fiber optical port (Single mode 1310nm TX 1550nm RX and 1550nm TX 1310nm RX), 2 E1 ports and 1 Fast-Ethernet port

FiberMix 3100-155 SDH Multi-Service multiplexer

If you need further information, please fill out this form below

What kind of information would you like to receive from us?

Please fill out the contact information:
First name/Last name: *
Company: *
E-mail: *
Your phone (country/city code): *

* Indicated a required field

DYNAMIX^®