DYNAMIX - is a leading supplier of broadband solutions: ADSL2+, SHDSL, HomePNA 3.0, VoIP, DSLAM, PowerLine. Modem, routers, multiplexer. Europe,Germany DYNAMIX - is a leading supplier of broadband solutions: ADSL2+, SHDSL, HomePNA 3.0, VoIP, DSLAM, PowerLine. Modem, routers, multiplexer. Europe,Germany DYNAMIX - is a leading supplier of broadband solutions: ADSL2+, SHDSL, HomePNA 3.0, VoIP, DSLAM, PowerLine. Modem, routers, multiplexer. Europe,Germany DYNAMIX - is a leading supplier of broadband solutions: ADSL2+, SHDSL, HomePNA 3.0, VoIP, DSLAM, PowerLine. Modem, routers, multiplexer. Europe,Germany
 

Home | Products | Support | Company News  |  Contact 

   На русском языке. DYNAMIX - оборудование широкополосного доступа: xDSL, ADSL, ADSL2+, SHDSL, HomePNA 3, VoIP, E1. Модемы, маршрутизаторы, мосты, концентраторы, шлюзы, стойки. Вектор, Украина, Россия  Українською мовою. DYNAMIX - обладнання широкополосного доступу: xDSL, ADSL, ADSL2+, SHDSL, HomePNA 3, VoIP, E1. Модеми, маршрутизатори, мости, концентратори, шлюзи, стійки. Вектор, Україна  
 
Frequently Asked Question of Dynamix VoIP equipment
Full firmware upgrade (2M-file) of Dynamix VoIP gateway via BOOT Mode

Attention !!!

Please read the following rules carefully before to start your firmware upgrade!!! 
The firmware upgrade is recommended only for experienced users! 

- You can upload the firmware to using terminal system and Ethernet interface. 
- Connect your VoIP gateway via Ethernet cable to PC 
- Connect VoIP gatway via console cable to RS-232 port
- HyperTerminal setup
Terminal configuration:
Speed rate : 9600 bps
Information bits: 8
Parity: No
Stop bits : 1
Flow control: No (<9600; 8N1; Flow Control: OFF>.)

- If on your VoIP gateway have not the label with MAC –Address, that you need for updating of 2M-file via BOOT Mode , you must request the vendor. 
- Power on your VoIP Gateway
Login: root 
Password:
(ENTER)

usr/config$ ifaddr -ifshow
cpm (unit number 0):
Flags: (0x8063) UP BROADCAST MULTICAST ARP RUNNING
Type: ETHERNET_CSMACD
Internet address: 10.1.1.3
Broadcast address: 10.255.255.255
Netmask 0xff000000 Subnetmask 0xff000000
Ethernet address is 00:01:a8:00:56:92
(write MAC-Address)
Metric is 0

- Reboot your gateway
- Show the following message and press ENTER

Attached TCP/IP interface to cpm unit 0
Attaching interface lo0...done
Please wait while system is initializing .........


- press ENTER
boot line : cpm(0,0)host:vxWorks h=10.1.1.2 e=10.1.1.3 u=vwusr pw=vw usr g=10.1.1.2
login : water
password : 3333

[help] , list all boot commands

<BOOT> h
b - program boot sector
c - change network address
d - use tftp download file
f - input tftp file name
g - go to ap
m - modify mac address
p - program ap sector
r - reset
s - show current network address
w - password set
x - show BOOT and AP version
z - program 2M rom file


<BOOT> c
- Please input your new network address.
- Tftp server addr: 10.1.1.2
(enter IP Address your PC and TFTP server)
- Target addr: 10.1.1.3 (enter IP -Address VoIP gateway)
- Gateway addr: 10.1.1.2 (enter IP - Address Default Gateway)
- Subnet mask of AP: 255.0.0.0 (enter Subnet Mask)

- Your input is
- Tftp server addr: 10.1.1.2
- Target addr: 10.1.1.3
- Gateway addr: 10.1.1.2
- Subnet mask of AP: 255.0.0.0

- if network address is correct,please press 'y' to
setup configuration,else press 'n' to continue

“Y”
(press <ENTER>

- bootline configuraton OK.
- auto reset


- After auto rebooting enter in BOOT Mode.

login : water
password : 3333


<BOOT> f (enter file name)
- Transfer File Name: 2m4fxo.118b
<BOOT> d
(download file from TFTP server)
download program.
- Load ....
Tftp transfer OK.
<BOOT> z
(reprogram Flash)
programming 2M rom file
- Be sure to program boot sector!!?(y/n): y
(Submit)
Please wait for a moment!!!
- programming OK.
<BOOT> r
(reboot gateway)
- software reset

After rebooting you must restore MAC-Address .

usr/config$ setmac
- enter mac address (xxxxxxxxxxxx): 0001a8005692
- the mac address is 00 01 a8 00 56 92
- if mac address is correct,please press 'y' to setup configuration,else press 'n' to continue


<y> (Submit)
- mac address configuraton OK.
usr/config$ flash –clean


 

Home | Technologies | Products | Company News  |  Contact 

DYNAMIX®