|
DYNAMIX UM-SN/3in1/ |
SHDSL NTU
with three DTE interfaces |
|
View Larger
Picture
|
Dynamix UM-SN/3in1/ - SHDSL NTU is a telecommunication product for carriers or SME users. Supporting
three DTE interfaces (E1, V.35 & Ethernet) in one device. Dynamix
UM-SN/3in1/ are designed to provide a flexible and efficient solution to handle various connections
Dynamix UM-SN/3in1/ as E1interface application offers two different ways to connect customers a high-speed TDM services with two G.703 E1 interfaces
(Balanced 120Ω RJ45 jack and Unbalanced 75Ω dual BNCs). The G.703 interface will carry from
64 kbps to 2.048 Mbps.
Dynamix UM-SN/3in1/ as Serial interface application offers the customers premise a high-speed TDM service with a DB25 interface. The industry standard DB25 interface can be configured as a V.35/RS530 or V.36/X.21 connection. The DB25 interface can transfers data up to
2.304 Mbps (2-wire).
|
User's manual
2.1
Mb
Quick start
|
Dynamix UM-SN/3in1/ as
Ethernet interface application offers the customers premise a high-speed TDM services with a LAN interface. The industry standard LAN interface can detect a 10M or 100M connection automatically.
Dynamix UM-SN/3in1/ SHDSL.bis NTU can be configured and managed via EOC, or menu-driven VT100 compatible Asynchronous Terminal Interface, either locally or
remotely.
Dynamix UM-SN/3in1/ is equipped with an auto rate capability that identifies the maximum line rate supported by the copper loop. This powerful automatic configuration capability makes installation and service provisioning simple and painless. Further flexibility is provided as the ability to manually set the maximum NTU speed at different levels for different customer-tailored service
offerings.
|
|
|
• |
Standard shdsl (ITU G.991.2) supports for improved reach/speed and greater interoperability |
• |
Fast and cost-effective provisioning of traditional frame relay
(FR or T-HDLC) or TDM leased line services |
• |
User existing copper loop infrastructures |
• |
Can operate back to back connection |
• |
Efficient single wire pair usage |
• |
Up to 2.304 Mbps symmetric service bit rate |
• |
Auto rate installation maximizes data rate based on loop conditions |
• |
Local management interface with LCD display |
• |
Remote line loopback |
• |
SHDSL Line performance monitoring |
• |
Raw and per time interval statistics |
Back to Top
|
|
|
|
WAN Interface |
| Line Rate: SHDSL per ITU G.991.2 |
| Coding: Trellis coded pulse amplitude modulation
(TC-PAM16) |
| Support:
Annex A (ANSI) and Annex B (ETSI) |
| Payload
rates: 64 kbps to 2.304 Mbps (N
x 64kbps, N=3 to 36) for Serial and Ethernet interface
64 kbps to 2.048 Mbps (N x
64kbps N=3 to 32) for E1 interface |
| Connection: RJ-45 jack (2-wire or 4-wire) |
| Impedance: 135 ohms |
G.703 Interface (as E1) |
| Connection:
RJ-45C for balanced 120Ω E1 cable
BNC for unbalanced 75Ω E1 cable |
| Line Rate :
2048 KHz +/- 50ppm |
| Framing : PCM30/PCM30C/PCM31/PCM31C and Unframed |
| Data Rate : 64
Kbps to 2.048 Mbps ( Nx64Kbps, N=1 to 32) |
| Operation : Full E1 and Fractional E1 |
Serial Interface (as RS-530/V.35/X.21) |
| Payload
rates: Up to 2.304 Mbps (N=1 to 36) |
| Connection:DB-25(F) |
| Support V.35/RS-530 or V.36/X.21 |
LAN Interface (as Ethernet) |
| Single Ethernet Interface |
| 10/100Mpbs Half/Full Duplex, Auto-sensing, Auto-MDI/MDIX |
| Up to
2048 MAC address learning, filtering bridge |
DSL Timing |
| Internal |
| From
E1 Recovery
(as E1) |
| From DTE (as V.35 and Ethernet) |
Performance Monitoring |
| ES, SES, UAS, LOSW, Alarms, Errors |
Loopback Tests
(for E1, T1 and V.35 interface only) |
| Local Digital Loopback |
| Local Loopback |
| Remote Line Loopback |
| Remote Payload Loopback |
| Far-end Line Loopback |
| Far-end Payload Loopback |
| V.54 Loopback (for V.35
interface) |
| Build-in 211-1 bit BER
tester |
Management |
| Configuration with keypad and LCD display |
| Console port (RJ45 , RS232C) |
| Support firmware upgradeable |
Physical/Electrical |
| Dimensions: 19.8 x 4.6 x 16.8 cm |
| AC Input: 90~240V with 50~60Hz |
| DC Input: -48V |
| Power
Consumption: 10W Max |
| Operation: 0 to 50°C |
| Humidity: Up to 95%
(non-condensing) |
|
Back to Top
|
|
|
|
|
|
DYNAMIX
UM-SN/3in1/AD
|
SHDSL NTU
with three DTE interfaces
2 power supply (AC
+ DC)
|
|
Back to Top |
|
|